potfit wiki

open source force-matching

User Tools

Site Tools


output:main

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
output [2013/03/01 09:58] danieloutput:main [2019/10/08 19:03] (current) slongbottom
Line 2: Line 2:
 ====== Output ====== ====== Output ======
 ---- ----
-//potfit// prints information on the minimization progress to the standard output. Additionally all input and output files used are also written to standard output. The output of the optimization will also be written to standard output unless the ''output_prefix'' parameter is set in the parameter file (which is strongly recommended).  
  
-=====  Potfit Output Files  =====+//potfit// prints information on the minimization progress to the standard output. Additionally all input and output file names are also written to standard output. 
  
-====  Final potential  ====+The output of the optimization will also be written to standard output unless the ''output_prefix'' parameter is set in the parameter file (which is highly recommended). 
  
-//potfit// always writes the potential achieved in minimization to a file using the same format as for the input potential. The name of this file is specified by the [[parameters|endpot parameter]].+=====  Potfit Output Files  =====
  
-====  Temporary Potential File  ====+====  Binned distribution file  ====
  
-Every now and then, depending on the algorithm usedan intermediate potential is written to a [[tempfile|tempfile]].+Only available for tabulated potentials: 
 +When compiled with the ''bindist'' option, a [[bindistfile]] can be created.
  
-====  IMD Potential File  ====+====  Error report  ====
  
-Prefix of files to which the [[http://imd.itap.physik.uni-stuttgart.de/|IMD]] potentials are written, see [[IMD]].+At the very end of each //potfit// run there will be an [[output::errors|error report]].
  
-====  Plotting files  ====+====  Final potential  ====
  
-Two files can generated to be used with gnuplot:  +//potfit// always writes the potential achieved in minimization to a file using the same format as for the input potential. The name of this file is specified by the [[:parameters|endpot parameter]].
-  * The [[plotfile|plotfile]] is always created +
-  * The [[plotpointfile|plotpointfile]] can be created for tabulated potentials if ''plotpointfile'' is set in the [[parameters|parameter file]].+
  
-====  Pair distribution file  ====+====  IMD Potential File  ====
  
-If ''write_pair'' is set to ''1'' in the [[parameters|parameter file]], the [[pair_distribution|pair distribution file]] will be written after the optimization.+Prefix of files to which the [[http://imd.itap.physik.uni-stuttgart.de/|IMD]] potentials are writtensee [[:imd|IMD]].
  
 ====  LAMMPS potential file  ==== ====  LAMMPS potential file  ====
  
-If ''write_lammps'' is set to ''1'' in the [[parameters|parameter file]], //potfit// will write a potential file for [[http://lammps.sandia.gov/|LAMMPS]]. This feature does not work for all potentials, for details see [[Lammps]]+If ''write_lammps'' is set to ''1'' in the [[:parameters|parameter file]], //potfit// will write a potential file for [[http://lammps.sandia.gov/|LAMMPS]]. This feature does not work for all potentials, for details see [[lammps|LAMMPS]].
- +
-====  Dist file  ==== +
- +
-For tabulated potentials: +
-When compiled with ''dist'' option, a [[distfile]] will be created.+
  
 ====  Output files  ==== ====  Output files  ====
Line 50: Line 43:
 All these files contain header lines, describing the following data. All these files contain header lines, describing the following data.
  
 +====  Pair distribution file  ====
 +
 +If ''write_pair'' is set to ''1'' in the [[:parameters|parameter file]], the [[pair_distribution|pair distribution file]] will be written after the optimization.
 +
 +====  Plotting files  ====
 +
 +Two files can generated to be used with gnuplot: 
 +  * The [[plotfile|plotfile]] is always created
 +  * The [[plotpointfile|plotpointfile]] can be created for tabulated potentials if ''plotpointfile'' is set in the [[:parameters|parameter file]].
 +
 +====  Temporary Potential File  ====
 +
 +Every now and then, depending on the algorithm used, an intermediate potential is written to a [[tempfile|tempfile]].
 +
 +====  Potential ensemble file  ====
 +
 +Only available for analytic potentials:
 +When compiled with the ''uq'' option, an [[ensemblefile]] can be created.
output/main.1362128293.txt.gz · Last modified: 2013/03/01 09:58 by daniel